
Kawasaki · MX
Cylinder block – Kawasaki MX80
Quick answer
The Kawasaki MX80 cylinder block is the barrel holding the piston bores that rotate around the drive shaft, governing the seal and efficiency of Kawasaki MX-series piston hydraulic units on excavators.
Việt Trung Hải, an authorized JIC Hydraulics distributor, carries JIC and genuine MX80 blocks to the same code that seal in the original unit, with a fast quote.
Not sure of the code? Send a photo of the pump nameplate or your machine model and our technicians will check it before you order.
- Part type
- Cylinder block
- Brand / pump line
- Kawasaki · MX
- Model code
- MX80
- SKU
- 2021-590-1-259
- Condition
- New, correct code
- Availability
- On request
What the MX80 cylinder block fits
The cylinder block is the barrel holding the piston bores that rotate around the drive shaft, where pistons reciprocate to move oil. The MX80 code belongs to Kawasaki's MX-series axial piston hydraulics, used in the pump/motor unit of excavator hydraulic systems. It is a directly loaded wear part: the face rides against the valve plate and the bores seal high-pressure oil, so surface flatness and finish set the whole unit's efficiency.
Signs it needs replacing
Weak or slow boom and swing under load, internal leakage, a scored or pitted block face, and oval-worn bores with piston play. Once scoring is deep, lapping rarely restores it—replace the block with its piston set.
Quality parts, fast quote
Việt Trung Hải is an authorized JIC Hydraulics distributor. JIC cuts the MX80 block to the same code, with proper heat treatment and bore tolerances for the fit, so it seals in the original unit with no reboring and no lapping of the face. Genuine blocks are stocked as well. Send your pump or motor code and photos for a compatibility check and fast quote.
Frequently asked questions
Which pump or motor does the MX80 cylinder block fit?
MX80 is a cylinder block for Kawasaki's MX-series axial piston hydraulics used in excavator pump/motor units. Send your unit code and photos and Việt Trung Hải will confirm exact compatibility before quoting.
When should I replace the whole block instead of lapping it?
Light dulling can be lapped, but deep scoring, pitting, or oval-worn bores that cause piston play and internal leakage mean the block should be replaced with its piston set to hold pressure and last.
Does a JIC MX80 block need reboring or lapping?
No. The face and bores on the JIC MX80 are cut to the original code and hardened to spec, so it seals against the existing valve plate with no trip to the grinder. Việt Trung Hải distributes JIC Hydraulics under authorization and carries genuine blocks. Send the code and photos for a fast quote.
Get a quote
Request a quote: Cylinder block – Kawasaki MX80
This is a quote model, not a cart. Send your machine model or pump code and we confirm fitment and quote fast.
Related parts
Kawasaki · MXRotary group kit – Kawasaki MX80MX80On requestView · get a quote
Kawasaki · MXRetainer plate – Kawasaki MX80MX80On requestView · get a quote
Kawasaki · MXValve plate – Kawasaki MX80MX80On requestView · get a quote
Kawasaki · MXPiston – Kawasaki MX80MX80On requestView · get a quote
Kawasaki · MXBall guide – Kawasaki MX80MX80On requestView · get a quote
Kawasaki · MXRotary group kit – Kawasaki MX150MX150On requestView · get a quote
Kawasaki · MXRotary group kit – Kawasaki MX173MX173On requestView · get a quote
Kawasaki · MXRotary group kit – Kawasaki MX750MX750On requestView · get a quoteTechnical handbook